Questions? Feedback? powered by Olark live chat software

How would I know about trailer bearings?!

Posted by Portsmouth Trailer on 17th Sep 2021

I have to admit it, when I was younger, I pulled a trailer for a couple of years, never suspecting that. there were bearings in the hubs that had to be serviced. I would later say, "How would I know about trailer bearings? Isn't it like a car? You don't have to service car bearings. Shouldn't someone tell you as a requirement of 'things you should know about trailers' in order to pull one?" Fortunately for me, I never had a bearing failure, but many find themselves on the side of the road, learning the hard way.

But what is a bearing failure? Technically, you could say:

  • The grease inside your hub has burned, boiled, or lost it's viscosity due to age, miles, heat, condensation, and/or water dilution. The grease will get brown and stinky or milky white.
  • If there wasn't enough lubricant to begin with, (which happens often straight from the factory), the bearing will spin itself dry and prematurely fail.
  • If the bearings are not adequately tight, (and not too tight), they may prematurely fail.
  • The seal is worn too much to contain the grease, so it leaks out and/or it let contaminants in.
  • The rollers and race surfaces have been damaged from excessive heat, looseness, or pitting from any of the above conditions. Once they have, a bearing can be thrown from the bearing cage, causing a melt down.

Metal on metal without lubricant is a ticking time-bomb. At first, the bearing with tarnish and turn golden brown, but soon, it can seize or catch fire. It is here where many will notice for the first time there is a problem because the wheel begins to wobble or smoke. It may be only minutes before the wheel seizes up, catches fire, or comes completely off and passes you on the highway, heading off into the woods, never to be found again. If you're lucky enough to safely pull over, you might find there is no way to continue and have to have the trailer wrecker-ed in to a shop like this, wait for your appointment date, and wait to find out if the axle can be saved. In many cases, the parts have welded themselves together or have wiped out too much of the metal to repair the spindle, which means you'll need a new axle, which means we have to fabricate a new one or order a new one from the manufacturer, which could take weeks.

These are all things that happen all the time in the trailer world. Surely, you've seen trailers on the shoulder of the highway. Yep, bearing failure. It's routine at our shop to build or order between 10 to 25 axles per month. Every month we have a mountain of axle carnage that we take to the dump. The good news is, all this is completely avoidable with just a little diligence and an understanding of WHY.

When it comes to trailer maintenance, brakes, lights, and emergency fail-safes are all important, but bearings should be #1 on your priority list because you don't know if you are road worthy until they are taken apart and inspected. Tires, at least, can be examined from the outside, and you can feel if your brakes are working, but the inside of your hubs are an unknown, so squirting some grease in them is not a viable solution.

The trailer industry has developed a "remove and replace" mentality in order to keep costs down. It's not a bad thing, (as long as the parts are still available.) But the good news is: you can keep or bring your trailer back to new! This also goes for your hub. Think of "re-building your hub' like "changing your oil" in your car. All the inner components of a hub are changeable and relatively cheap. When servicing a hub, ( a "Repack"), we pull the tire and wheel, remove the hub, take out the seal, clean the old grease out and inspect the parts. If the grease is burned, rusty, or any parts are discolored, pitted or scratched, all parts are changed for new. So, good parts, a new seal, a properly packed hub, a new cap, and a properly tightened axle nut, and you are good to go under most conditions.

Note: There are differing views on what "properly packed" means, but here at Portsmouth Trailer, we fill the hub almost all the way with grease to insure the bearing stays lubricated as well as displacing any water or other contaminants At normal trailer speeds, we don't have to contend with "Churning", "Skating", or "Grease Separation" that other high speed applications may be concerned with.

Naturally, the most popular question we get is "How often do I need to service my hubs?" And, of course, there are too many variables to be able to answer that accurately since usage, cargo, size, weight, mileage, brake heat, going in salt­water, etc. all play a part. But our typical answer is "Servicing your bearings once a year is a safe way to stay off the side of the road." There is also a quick check you can perform at any time. It's not definitive, but could give you a heads up: Get in front of your trailer wheel and with both hands, grab the top of the tire. Now, pull and push it back and forth. If there is more than just a little movement in the bearings, you will feel it, and you should address it ASAP. (You may need to jack the trailer up if it's a bigger trailer.) It could be just a loose nut, improperly tightened, or it could be the beginning of a bearing failure. Don't ignore it!

As Grandpa always said, "An ounce of prevention is worth a pound of cure"

Thanks from the folks at Portsmouth Trailer Supply!